discount coupon €120 off

Frizzlife 800 GPD tankless reverse osmosis system – remineralization, PD800-TAM4

Model: PD800-TAM4
Fast tankless RO water with mineral balance

€539,99 €659,99
€120 off
€120 off
CODE: JDE120

Certification

Testing performed under NSF/ANSI standards 42&53&58. This system has been tested according to NSF/ANSI 42&53&58 for the reduction of substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permittable limit for the water leaving the filter as specified in NSF/ANSI 42&53&58
Buy now

Service & Benefits

Fast,Free Shipping For Order Over $25
One-year free warranty(Register to get 150% coverage)
30-Day Return,No Worries guarantee
Lifetime Customer Support
Pay with Ease :
  • PayPal
  • American Express
  • Mastercard
  • Discover
  • Klarna
PD800-TAM4 remineralized alkaline reverse osmosis system showing mineral balance and pH scale
Alkaline, remineralized water in a balanced ratio

PD800-TAM4: Balanced, remineralized and slightly alkaline RO water

The PD800-TAM4 is a tankless reverse osmosis system with 800 GPD and a downstream remineralization filter. After RO filtration, the TAM4 stage adds selected minerals and maintains a slightly alkaline pH range – for a pleasantly mild taste in everyday use.

This makes the PD800-TAM4 ideal for anyone who wants to combine the advantages of an under-sink reverse osmosis system with a more harmonious taste after remineralization.

Tankless 800 GPD RO system with remineralization
TAM4 post-filter for remineralization
Supports a slightly alkaline pH range
For pleasant-tasting drinking water in everyday life
PD800-TAM4 2:1 pure to drain ratio comparison showing water saving efficiency
2:1 clean water-wastewater ratio + water-saving operation

Efficient RO filtration with a 2:1 purified water-to-wastewater ratio

The PD800-TAM4 operates with an advanced, water-saving 2:1 purified water-to-wastewater ratio. This means that when dispensing 2 cups of purified water, only 1 cup of wastewater is produced.

The system is therefore designed for higher water efficiency than conventional RO systems with a larger proportion of wastewater.

2:1 clean water-wastewater ratio
2 cups of clean water : 1 cup of wastewater
Water-saving design as shown in the product graphic
Wastewater can be reused for suitable purposes outside the drinking water sector.
PD800-TAM4 800 GPD fast flow reverse osmosis system filling glass quickly
High-performance water flow rate of 800 GPD

High 800 GPD capacity for daily water needs

The PD800-TAM4 offers a filter capacity of up to 800 gallons per day, ensuring a strong, consistent water output for daily household use.

A glass with approximately 240 ml (8 oz) can be filled in less than 7 seconds – ideal for kitchens with a regularly high water demand.

Filter capacity of 800 GPD
Fast, consistent water flow
Approximately 240 ml (8 oz) in under 7 seconds
Ideal for households with high water consumption
PD800-TAM4 smart faucet display showing TDS OUT value and filter status indicators
Intelligent TDS panel with real-time display

Smart faucet with OUT-TDS display and color-coded status

The integrated smart tap provides up-to-date information on the system status at all times via color-coded displays and the OUT-TDS display.

Instead of guessing, you can quickly recognize the system status using intuitive visual signals. The color indicator shows whether water quality and filter condition are within the normal range or whether maintenance is required.

This makes daily monitoring particularly easy and allows you to see in good time when a filter change is due.

The display also shows the OUT TDS values as well as status indicators for CP and RO operation.

OUT-TDS real-time display
Color-coded display system for filter status
For simple and timely maintenance checks
PD800-TAM4 tankless all-in-one reverse osmosis system showing no tank and leak reduction design
Tankloses ALL-IN-ONE-Design

Space-saving all-in-one design without a tank

The PD800-TAM4 features a compact all-in-one design without a tank, saving space under the sink and simplifying system setup.

Since no storage tank is required and fewer connection points are needed, the integrated design helps to reduce potential leakage risks and problems caused by temporarily stored water.

Tankless RO system design
No storage tank required
Space-saving under-table design
Fewer connection points
Designed to reduce potential leakage risks
PD800-TAM4 quick install and single twist filter replacement system
Installation & Filterwechsel

Quick installation and filter change in approximately 2 seconds.

The PD800-TAM4 is designed for easy installation with guided setup. Thanks to the one-turn mechanism, the filters can be changed particularly quickly.

The step-by-step instructions allow the installation to be completed in less than 30 minutes.

Installation in less than 30 minutes (<30 min.)
Filter change with just one twist
Filter change in approximately 2 seconds
Suitable for self-assembly
PD800-TAM4 RO system connected to refrigerator ice maker and mini tank expansion accessories
Versatile use & expansion options

Connection options for refrigerator, ice maker and mini tank

With suitable accessories, the PD800-TAM4 supports various applications, including connection to a refrigerator and ice maker via the IMC-1 kit.

The optional MWT3 mini-tank is also available, which supports pressure-dependent applications and offers more flexibility in different installation situations.

Supports connection of refrigerator/ice maker via IMC-1
Compatible with the MWT3 mini tank
Flexible use for various applications
Designed for extended household installations

Discover more tankless RO systems

The PD800-TAM4 is a powerful choice for households that want high RO water flow, remineralized taste and intelligent monitoring at the tap in a space-saving under-counter system.

NSF/ANSI Standards

View Report

ANSI 372

Lead Content Compliance for Drinking Water Contact Materials
NSF/ANSI/CAN 372 is a standard used to evaluate the lead content of materials and components that come into contact with drinking water. Products tested to this standard are evaluated against lead content requirements for drinking water system materials.
This standard focuses on lead content in water-contact materials. It should not be confused with contaminant reduction performance standards such as NSF/ANSI 42, 53, or 58.

Specs

Model
PD800-TAM4
Use Cases
Under-Sink
Flow Rate
0.56 GPM / 800GPD
Dimensions
PD800: 5.3"L x 14.7"W x 15.5"
TAM4: 5" x 5" x 13.5"
GPD
800
Drain ratio
2:1
Speicherlos
Installation
Need Installation
Drill a hole in the countertop
Electricity Required
Remineralization
Certification Explanation

NSF/ANSI 372
SGS Certified

Purification Method

0.0001 μm Reverse Osmosis Filtration
Alkaline/Remineralize

Material

1. Pleated Carbon Compound filter
2. 800G RO membrane,
3. Alkaline Remineralization filter
4. Stainless steel faucet with brushed nickel finish.

User manual

FAQ

Why there are many white bubbles in the water?

Normally for the first time use of the RO system, the water seems to have white bubbles in it,which is normal and totally drinkable. It is because when the pump is pressurizing the water, it will pressurize the air at the same time. It will make the air molecules smaller, thus the solubility further increases. The air can’t be released at that time because of the pressure in the RO system.
However, when you turn on the tap to get a cup of water, the pressure of air is released. So you will see a huge number of bubbles in the water. It looks cloudy and white, but they are just bubbles. After you put the water still for a while, all bubbles will be gone, the water is totally good for drinking.

TDS tester pen shows higher result than the TDS number displayed on the PD800-TAM4?

It is because the TAM4 filter, the post filter, adds the minerals to the water. Normally the TAM4 will increase the TDS by 10-30 ppm.
If the system hasn’t been used for a while, the TAM4 will restore more minerals to the water, and at that time the water is very good, the PH level will be more than 9.

Why TDS is higher at the beginning, but back to normal range after about one minute?

Osmosis is a natural phenomenon happens in all RO system, no matter if you have a conventional RO system or tankless RO system.

When the RO system starts to work, pressure from the pump overcomes natural osmotic pressure, forcing feed water through the RO membrane that removes the impurities.

When the RO system stops working, the pump stops offering pressure as well.

At that time, because of different concentrations, a small fraction of ions will enter into pure water and cause TDS to rise by a small amount.

However, even if the TDS reading is a little high at the beginning, the quality water is still unbeatable by any other filtration methods including carbon, KDF, ceramic, UF, UV, etc.

The water is totally good to drink and you don’t have to wait for about 1 minute to get the water, since the whole system will not release any harmful substances to the water.

The TDS removing rate for PD800-TAM3 is about 94–95%, if your incoming TDS is high, the outlet TDS will be high too.

How does the TDS display on the machine work?

When the system is running, the TDS sensor in the PD800-TAM4 will keep testing the water quality every 1 minute. Therefore, the TDS result you see from the machine is from the last test memory.

If you want to have the real-time TDS result, please let the machine run for about 1 minute.

If I don’t want to use the TAM4, how should I disconnect it?

You don’t have to disconnect the tubing and the fittings on the TAM4. You only need to unscrew the TAM4 filter and the water still can go through.

Installation video

Reviews

Frizzlife

Frizzlife 800 GPD tankless reverse osmosis system – remineralization, PD800-TAM4

€539,99 €659,99
PD800-TAM4 remineralized alkaline reverse osmosis system showing mineral balance and pH scale
Alkaline, remineralized water in a balanced ratio

PD800-TAM4: Balanced, remineralized and slightly alkaline RO water

The PD800-TAM4 is a tankless reverse osmosis system with 800 GPD and a downstream remineralization filter. After RO filtration, the TAM4 stage adds selected minerals and maintains a slightly alkaline pH range – for a pleasantly mild taste in everyday use.

This makes the PD800-TAM4 ideal for anyone who wants to combine the advantages of an under-sink reverse osmosis system with a more harmonious taste after remineralization.

Tankless 800 GPD RO system with remineralization
TAM4 post-filter for remineralization
Supports a slightly alkaline pH range
For pleasant-tasting drinking water in everyday life
PD800-TAM4 2:1 pure to drain ratio comparison showing water saving efficiency
2:1 clean water-wastewater ratio + water-saving operation

Efficient RO filtration with a 2:1 purified water-to-wastewater ratio

The PD800-TAM4 operates with an advanced, water-saving 2:1 purified water-to-wastewater ratio. This means that when dispensing 2 cups of purified water, only 1 cup of wastewater is produced.

The system is therefore designed for higher water efficiency than conventional RO systems with a larger proportion of wastewater.

2:1 clean water-wastewater ratio
2 cups of clean water : 1 cup of wastewater
Water-saving design as shown in the product graphic
Wastewater can be reused for suitable purposes outside the drinking water sector.
PD800-TAM4 800 GPD fast flow reverse osmosis system filling glass quickly
High-performance water flow rate of 800 GPD

High 800 GPD capacity for daily water needs

The PD800-TAM4 offers a filter capacity of up to 800 gallons per day, ensuring a strong, consistent water output for daily household use.

A glass with approximately 240 ml (8 oz) can be filled in less than 7 seconds – ideal for kitchens with a regularly high water demand.

Filter capacity of 800 GPD
Fast, consistent water flow
Approximately 240 ml (8 oz) in under 7 seconds
Ideal for households with high water consumption
PD800-TAM4 smart faucet display showing TDS OUT value and filter status indicators
Intelligent TDS panel with real-time display

Smart faucet with OUT-TDS display and color-coded status

The integrated smart tap provides up-to-date information on the system status at all times via color-coded displays and the OUT-TDS display.

Instead of guessing, you can quickly recognize the system status using intuitive visual signals. The color indicator shows whether water quality and filter condition are within the normal range or whether maintenance is required.

This makes daily monitoring particularly easy and allows you to see in good time when a filter change is due.

The display also shows the OUT TDS values as well as status indicators for CP and RO operation.

OUT-TDS real-time display
Color-coded display system for filter status
For simple and timely maintenance checks
PD800-TAM4 tankless all-in-one reverse osmosis system showing no tank and leak reduction design
Tankloses ALL-IN-ONE-Design

Space-saving all-in-one design without a tank

The PD800-TAM4 features a compact all-in-one design without a tank, saving space under the sink and simplifying system setup.

Since no storage tank is required and fewer connection points are needed, the integrated design helps to reduce potential leakage risks and problems caused by temporarily stored water.

Tankless RO system design
No storage tank required
Space-saving under-table design
Fewer connection points
Designed to reduce potential leakage risks
PD800-TAM4 quick install and single twist filter replacement system
Installation & Filterwechsel

Quick installation and filter change in approximately 2 seconds.

The PD800-TAM4 is designed for easy installation with guided setup. Thanks to the one-turn mechanism, the filters can be changed particularly quickly.

The step-by-step instructions allow the installation to be completed in less than 30 minutes.

Installation in less than 30 minutes (<30 min.)
Filter change with just one twist
Filter change in approximately 2 seconds
Suitable for self-assembly
PD800-TAM4 RO system connected to refrigerator ice maker and mini tank expansion accessories
Versatile use & expansion options

Connection options for refrigerator, ice maker and mini tank

With suitable accessories, the PD800-TAM4 supports various applications, including connection to a refrigerator and ice maker via the IMC-1 kit.

The optional MWT3 mini-tank is also available, which supports pressure-dependent applications and offers more flexibility in different installation situations.

Supports connection of refrigerator/ice maker via IMC-1
Compatible with the MWT3 mini tank
Flexible use for various applications
Designed for extended household installations

Discover more tankless RO systems

The PD800-TAM4 is a powerful choice for households that want high RO water flow, remineralized taste and intelligent monitoring at the tap in a space-saving under-counter system.

Show product
Copied successfully!